FAQ
- With this flywheel work with adapting a gen 1 sbc with a 2 piece rms to a 97 t56 using a napa 1104134 clutch kit?
- Will this part fit a 2006 Dodge Ram Power wagon?
- Will this kit work with the stock flywheel?
- Will this fit my 2000 Audi TT Quattro 5 speed ? Your website doesn’t let me specify that it is a Quattro or not. They are different, also I am aware I will need the 1989-91 228 mm Corrado G60 flywheel if it does fit my vehicle.
- Will this fit a stock flywheel?
- Will this clutch system operate properly for close to stock Horsepower-Ft lbs. On a 1998 camaro z28 w/ long tube headers and loudmouth 2 exhaust LS1 5.7L engine? Stock torque factors are 345 ft lbs @4200 rpms this specific clutch advertises @ 400+
- Will this clutch and flywheel kits fit 2014 Jeep JK Rubicon? Is there any Centerforce authorized work shop in northeast Georgia area?
- What kind of power can I expect this clutch to support?
- What is your thoughts about the bell housing interference for a 1967 GT500? This will work with stock flywheel resurfaced correct? Or would you suggest a different combination?
- What is the differente between DF395010 and DF593010? They both fit LS1 flat flywheell. I have the centerforce 700142 flywheel on a 2008 LS3 mated to a T56.
- What is included with this kit?
- Quisiera un disco de embrague para cambiar el original de goma (Porsche 944 motor M44.02/.04), solo disco Se pueden utilizar la misma prensa de embrague o hay cambiarlo todo? Cuál es el adecuado?
- many years ago I purchased a Centerforce flywheel ,clutch & pressure plate . PN:700120 . my question is what is the number of teeth on the flywheel ?Regards , Steve...
- looking for full clutch kit for 2008 Jeep Wrangler Unlimited Sahara 3.8 liter 4X4
- Is this kit available with a disc that will work with an 1-1/8 10 spline input shaft from a NV4500 transmission?
- Is this just the pressure plate , so i will know to order the clutch disc ? Thank you .
- Is it normal to have a clicking sound all the time? and when you press the gas pedal it sounds more?
- I'm considering purchasing flywheel pn 600142, however I need to know what the distance is across the open area on the recessed area on the friction side of the flywheel.
- I wanted to know if the Centerforce DF070552 will bolt to my Hays 11-430 flywheel?The 143 tooth Flywheel will accept the 11” disk but I’m unclear as to if the diaphragm type pressure bolt pattern will work.Hays has conflicting information on the plate
- I recently installed an NV4500 transmission with an 1-1/8” 10 spline input shaft. Can I get this clutch kit with a disc to work for my setup?
- I need to buy just the clutch plate
- I need aclutch that direct fit with stock flywheel ,for my 1996 corvette grandsport .and perform better , stronger than factory clutch
- I have a NV4500 transmission with a 1 3/8" ten tooth input shaft mated to my Gen VI 454 producing about 430 HP. What series II disc and pressure plate can I use with this 700146 flywheel?
- I have a Gen 1 350 that is being turned into a 383 stroker. Will the following clutch and pressure plate with Centerforce flywheel 700160? CF165473S and 383735. Thanks
- I currently have your clutch and flywheel kit in my car but the disc is toast. What would be the best replacement disc for my setup. Mostly street but flywheel hp is 550-700 with nitrous it is a single disc setup thank you
- I am purchasing a Tremec 5 speed for my '75 Corvette. I have a Centerforce Dual Friction clutch that has less than 500 miles on it and need the 26 spline disc. Is the 384148 disc the correct replacement? The previous one is an 11", 10 or 11 spline for my
- I am looking for the best clutch for my jeep. It has 39" tires 14.5 wide and run 456 gears. still run the 4.0 engine with some mods.
- I am looking for a hydraulic throwout bearing for a Coyote/ TKO 600. HELP
- I AM INSTALLING CLUTCH KIT KDF931042 INTO A 2000 CORVETTE. IS THERE A SHIM SPEC FOR THE DISTANCE BETWEEN THE PRESSURE PLATE AND THROW OUT BEARING? I HAVE A FACTORY SLAVE ACTUATOR, THANK YOU
- How much torque is safe with one of these clutches? I'm trying to figure out what disk to get to replace one I had with this series. This engine was dyno'd at 525HP, 530 Lb Ft of TQ. Would this disk be safe to use for that combo?
- Hi! I would like to know if you guys produce/make a clutch for Suzuki Swift 91 turbo? It has 500whp and 330 torque
- Hi I have a 454 that I'm going to be building for my Impala. It will be a street car. I'll probably run up to 750 hp. It will have a T56 behind it and I'm just wondering if your flywheel or no. 700140 is correct for the application?
- Hello, I am looking for the correct fitment for a throwout bearing. The application is a 1992 Firehawk Firebird Formula. 350 Small Block ZZ1 crate motor with a ZF 6 speed transmission. Centerforce clutch, GM V8 clutch fork. The part I removed was #614018.
- Does this unit contain Flywheel?
- Does this clutch kit include the throwout bearing?
- Does the centerforce pilot bearing have a 1.095 OD, or is it possible that it runs wider? Asking because my Crankshafts hole is worn, and a stock 1.094 OD size is now to small.
- Does my centerforce clutch use alignment dowels. 1970 Mach1 351c
- Centerforce DYAD DS P/N 08614842 Installing on a built single Turbo LS 408 with TKO600 5 Speed. My question is: Will this 10.4" DYAD XDS dual clutch system fit under my QuickTime bellhousing? Also, will it work with my American Powertrain HydroMax hydraul
- Can I get a better price on this clutch kit if I order by tomorrow morning
- Best twin disc and throw out bearing for 2003 c5 zo6 corvette 693 hp at the crank
- After 50 years & over 120,000 miles it’s time to rebuild my GTX, including replacing the clutch. A friend recommended Centerforce but as I research it I’m uncertain which of your clutch models are correct for me. It’s a stock rebuild & the transmiss
- 84 corvette trying to install a s6-40 zf no dualmass flywheel and a pull style clutch diaphramcrank is a 2 piece oilseal wth center h.h. of 2.486unable to find the right combo !
Q: With this flywheel work with adapting a gen 1 sbc with a 2 piece rms to a 97 t56 using a napa 1104134 clutch kit?
Yes
Q: Will this fit my 2000 Audi TT Quattro 5 speed ? Your website doesn’t let me specify that it is a Quattro or not. They are different, also I am aware I will need the 1989-91 228 mm Corrado G60 flywheel if it does fit my vehicle.
We do not list clutch for a 2000 TT Quattro
Q: Will this clutch system operate properly for close to stock Horsepower-Ft lbs. On a 1998 camaro z28 w/ long tube headers and loudmouth 2 exhaust LS1 5.7L engine? Stock torque factors are 345 ft lbs @4200 rpms this specific clutch advertises @ 400+
Yes
Q: Will this clutch and flywheel kits fit 2014 Jeep JK Rubicon? Is there any Centerforce authorized work shop in northeast Georgia area?
Yes fits your Jeep.
Q: What kind of power can I expect this clutch to support?
The holding capacity for part number 315536010 is 399 ft/lbs of torque.
Q: What is your thoughts about the bell housing interference for a 1967 GT500? This will work with stock flywheel resurfaced correct? Or would you suggest a different combination?
Please call the tech line 928-771-8422
Q: What is the differente between DF395010 and DF593010? They both fit LS1 flat flywheell. I have the centerforce 700142 flywheel on a 2008 LS3 mated to a T56.
DF593010 has bleed plug kit, DF395010 does not.
Q: What is included with this kit?
Pressure plate and bolts, disc, alignment tool, pilot and release bearings
Q: Quisiera un disco de embrague para cambiar el original de goma (Porsche 944 motor M44.02/.04), solo disco Se pueden utilizar la misma prensa de embrague o hay cambiarlo todo? Cuál es el adecuado?
Please call the tech line 928-771-8422
Q: many years ago I purchased a Centerforce flywheel ,clutch & pressure plate . PN:700120 . my question is what is the number of teeth on the flywheel ?Regards , Steve...
Part# 700120 has 168 teeth. Part# 700160 has 168 teeth.
Q: looking for full clutch kit for 2008 Jeep Wrangler Unlimited Sahara 3.8 liter 4X4
This kit fits your 2008 Jeep Wrangler Unlimited Sahara 3.8L 4X4.
Q: Is this kit available with a disc that will work with an 1-1/8 10 spline input shaft from a NV4500 transmission?
DF024909 has a 1-1/8"-10 spline disc
Q: Is this just the pressure plate , so i will know to order the clutch disc ? Thank you .
Only the pressure plate in included.
Q: Is it normal to have a clicking sound all the time? and when you press the gas pedal it sounds more?
Please call the tech line 928-771-8422
Q: I'm considering purchasing flywheel pn 600142, however I need to know what the distance is across the open area on the recessed area on the friction side of the flywheel.
Please call the tech line 928-771-8422
Q: I wanted to know if the Centerforce DF070552 will bolt to my Hays 11-430 flywheel?The 143 tooth Flywheel will accept the 11” disk but I’m unclear as to if the diaphragm type pressure bolt pattern will work.Hays has conflicting information on the plate
Pressure plate has #2 pattern see clutch bolt pattern guide found under downloads
Q: I recently installed an NV4500 transmission with an 1-1/8” 10 spline input shaft. Can I get this clutch kit with a disc to work for my setup?
DF024909 has a 1-1/8"-10 spline disc
Q: I need to buy just the clutch plate
Sorry the disc in the kit is not sold separately. You could use Centerforce I disc part# 384100
Q: I need aclutch that direct fit with stock flywheel ,for my 1996 corvette grandsport .and perform better , stronger than factory clutch
This kit is rated 591 ft/lbs of torque at the crank. Bolts to factory Dual-Mass flywheel.
Q: I have a NV4500 transmission with a 1 3/8" ten tooth input shaft mated to my Gen VI 454 producing about 430 HP. What series II disc and pressure plate can I use with this 700146 flywheel?
Sorry we do not have parts for the conversion.
Q: I have a Gen 1 350 that is being turned into a 383 stroker. Will the following clutch and pressure plate with Centerforce flywheel 700160? CF165473S and 383735. Thanks
Please give the tech line a call for 928-771-8422
Q: I currently have your clutch and flywheel kit in my car but the disc is toast. What would be the best replacement disc for my setup. Mostly street but flywheel hp is 550-700 with nitrous it is a single disc setup thank you
This kit is rated 700 ft/lbs of torque at the crank. Replacement disc part# DF382612.
Q: I am purchasing a Tremec 5 speed for my '75 Corvette. I have a Centerforce Dual Friction clutch that has less than 500 miles on it and need the 26 spline disc. Is the 384148 disc the correct replacement? The previous one is an 11", 10 or 11 spline for my
Yes correct disc for Tremec conversion with 1-1/8"-26 spline input.
Q: I am looking for the best clutch for my jeep. It has 39" tires 14.5 wide and run 456 gears. still run the 4.0 engine with some mods.
This clutch kit is the best choice for a jeep with your modifications.
Q: I am looking for a hydraulic throwout bearing for a Coyote/ TKO 600. HELP
This is designed for the stock transmission. Will not work with TXO 600.
Q: I AM INSTALLING CLUTCH KIT KDF931042 INTO A 2000 CORVETTE. IS THERE A SHIM SPEC FOR THE DISTANCE BETWEEN THE PRESSURE PLATE AND THROW OUT BEARING? I HAVE A FACTORY SLAVE ACTUATOR, THANK YOU
Kit does not come with any shims
Q: How much torque is safe with one of these clutches? I'm trying to figure out what disk to get to replace one I had with this series. This engine was dyno'd at 525HP, 530 Lb Ft of TQ. Would this disk be safe to use for that combo?
Rated 586 ft/lbs of torque at the crank, when used with Centerforce Dual Friction pressure plate.
Q: Hi! I would like to know if you guys produce/make a clutch for Suzuki Swift 91 turbo? It has 500whp and 330 torque
Sorry we do not have any rated at 330
Q: Hi I have a 454 that I'm going to be building for my Impala. It will be a street car. I'll probably run up to 750 hp. It will have a T56 behind it and I'm just wondering if your flywheel or no. 700140 is correct for the application?
This flywheel fits 1970-1990 2pc rear seal, 33 in/oz
Q: Hello, I am looking for the correct fitment for a throwout bearing. The application is a 1992 Firehawk Firebird Formula. 350 Small Block ZZ1 crate motor with a ZF 6 speed transmission. Centerforce clutch, GM V8 clutch fork. The part I removed was #614018.
Yes this is the correct bearing.
Q: Does the centerforce pilot bearing have a 1.095 OD, or is it possible that it runs wider? Asking because my Crankshafts hole is worn, and a stock 1.094 OD size is now to small.
O.D. is 1.095, roller bearing
Q: Does my centerforce clutch use alignment dowels. 1970 Mach1 351c
This pressure plate does not use dowel pins. 5/16” shouldered bolts part# 33002 are used.
Q: Centerforce DYAD DS P/N 08614842 Installing on a built single Turbo LS 408 with TKO600 5 Speed. My question is: Will this 10.4" DYAD XDS dual clutch system fit under my QuickTime bellhousing? Also, will it work with my American Powertrain HydroMax hydraul
Clutch will work with bellhousing designed for LS application. When using an aftermarket hydraulic release bearing it is important to check for proper clearance between the bearing and the centrifugal weight system.
Q: Can I get a better price on this clutch kit if I order by tomorrow morning
The price listed on website at time of purchase, cannot be modified.
Q: Best twin disc and throw out bearing for 2003 c5 zo6 corvette 693 hp at the crank
Twin disc clutch options are a 413614842 DYAD DS for street/light track use or a 413514842 DYAD XDS for track use.
Q: After 50 years & over 120,000 miles it’s time to rebuild my GTX, including replacing the clutch. A friend recommended Centerforce but as I research it I’m uncertain which of your clutch models are correct for me. It’s a stock rebuild & the transmiss
Please give the tech line a call for 928-771-8422